How much fragrance oil goes into 1 lb of soy wax?

Updated ยท 4 min read

Fragrance load is usually calculated against the wax weight, not the final combined candle weight. The candle wax calculator follows that convention: fragrance weight equals wax weight multiplied by the percentage expressed as a decimal.

Use the wax and fragrance calculator to check jar-based batches, but keep your starting units straight. This guide starts with a known pound of wax. It shows exact percentages instead of relying on the common approximation of one ounce of oil per pound.

Try the Candle Wax Calculator

Enter your own numbers. Nothing you type leaves your device.

Open the full Candle Wax Calculator

Calculate the load from 16 ounces of wax

One avoirdupois pound equals 16 ounces by weight. At 6%, multiply 16 by 0.06 to get 0.96 ounces of fragrance. At 8%, multiply by 0.08 to get 1.28 ounces. At 10%, multiply by 0.10 to get 1.60 ounces. These are separate additions to the wax.

For gram conversions, one ounce by weight is 28.349523125 grams. Multiplying the three oil quantities by that conversion gives the rounded values in the table. Use grams consistently for both ingredients if your scale is easier to read that way; do not mix fluid ounces with weight ounces.

Fragrance for exactly 1 lb of wax
Load on wax weightOil, oz by weightOil, gramsCombined wax and oil, oz
6%0.9627.2216.96
8%1.2836.2917.28
10%1.6045.3617.60

Distinguish exact percentages from a handy shortcut

CandleScience describes a 6% starting load for AAK 464 as approximately one ounce per pound of wax. The word approximately matters: 1 / 16 times 100 = 6.25%. One ounce per pound is therefore close to 6%, but it is not mathematically identical.

For an exact 6% recipe, use 0.96 ounces rather than silently treating one ounce as the same amount. Either approach needs a clearly recorded formula. Consistency helps you compare tests, especially when changing a fragrance or investigating a candle that performs differently from an earlier batch.

Reproduce the calculation with the site's jar model

The calculator begins with a container volume rather than a direct wax-weight input. Internally, it uses wax ounces = container fluid ounces times 0.86. To verify a 16-ounce wax basis numerically, a volume input of 16 / 0.86, approximately 18.60465116 fluid ounces, produces 16 ounces of estimated wax.

With one candle and an 8% load, that mathematical setup returns 1.28 ounces of fragrance. It is a formula check, not a recommendation to pour a pound of wax into any jar with that nominal volume. Actual blend capacity needs physical measurement, and fragrance is added after the wax estimate in this implementation.

Check the wax specification before choosing a percentage

CandleScience recommends starting at 6% for AAK 464 soy wax and lists 10% as that wax's maximum fragrance load. The supplier also warns that more fragrance may cause burn issues and may not create a stronger scent. A maximum is a ceiling for that product, not a target.

Other waxes and fragrances can have different requirements. Check the current product instructions, applicable fragrance-use limits, and the compatibility of your chosen materials. The lower applicable restriction governs your recipe. A calculator can perform arithmetic at a requested percentage without validating a wax formulation or proving the candle burns properly.

Weigh, label, and test a repeatable batch

For the 8% example, weigh the wax and 36.29 grams of oil separately using a scale appropriate to the batch size. Keep written notes on the wax product, fragrance, load, wick, jar, and processing instructions followed. Do not improvise mixing temperatures from a percentage calculation.

Test the finished candle over its intended burn life, and compare results before increasing the load. If you start with a fixed finished-blend weight rather than a fixed wax weight, the formula changes: wax = total / (1 + load), and oil is the remainder. Confusing those starting points changes the recipe even when the percentage label looks identical.

Frequently asked questions

No. One ounce divided by 16 ounces is 6.25%. An exact 6% load uses 0.96 ounces of oil per pound of wax.

Sources