How much epoxy resin do I need for a 10-foot river table?
Updated · 3 min read
A long river table can consume much more resin than its finished surface suggests. Use the epoxy resin calculator to estimate the empty channel between your slabs. The important dimensions are channel length, average width, and actual fill depth, all entered in inches.
Before buying a kit, compare several measurements in the river table volume calculator. A winding live edge rarely forms a perfect rectangle. Treat the result as an estimate for purchasing, then verify the mold, product instructions, and planned pour schedule before mixing anything.
Try the Epoxy Resin Calculator
Enter your own numbers. Nothing you type leaves your device.
1/8 inch (0.125) is a typical flood coat. Check your product's maximum pour depth.
Total epoxy needed
87.8 fl oz
0.69 gallons or 2.6 liters
Mix amounts by volume
- Part A resin
- 43.9 fl oz
- Part B hardener
- 43.9 fl oz
- Volume
- 158.4 in³
Measure the cavity rather than the tabletop
For a nominal 10-foot river, enter 120 inches as the length. Measure width at several locations along the channel. If those locations represent equal lengths, their average gives a useful starting width. For sharply changing shapes, calculate smaller rectangular segments and add their volumes instead.
Depth means the space that epoxy will actually occupy. A slab may be thicker than the river fill because you plan to flatten or finish the surface later. Include voids and large cracks separately, and do not assume a full tabletop flood coat is included in the river calculation.
Work through an 8-inch-wide example
The basic formula is length times width times depth. Here, 120 times 8 times 2 equals 1,920 cubic inches. Divide by 231 cubic inches per US gallon to get 8.31 gallons of combined resin and hardener. Multiplying by 1.10 gives 2,112 cubic inches, or 9.14 gallons.
With an illustrative 2:1 ratio by volume, the calculator divides that total into 780.19 fluid ounces of resin and 390.10 fluid ounces of hardener. Those are project totals, not instructions to combine everything in one bucket. Only use that ratio when your selected product specifically requires it.
Compare river widths before placing an order
These variations keep the length at 120 inches, depth at 2 inches, and waste at 10%. The quantities represent mixed epoxy, including both components. A wider river increases volume directly, so careful slab positioning can materially change the amount you need.
Round the purchasing amount to available kit sizes without rounding the component ratio. Keep the measuring ratio exact for every batch, even when a kit leaves some material unused. Extra stock is useful only if it is the correct resin and matching hardener for the selected system.
| Average width | Mixed gallons | Mixed liters |
|---|---|---|
| 6 in | 6.86 | 25.96 |
| 8 in | 9.14 | 34.61 |
| 10 in | 11.43 | 43.26 |
Choose a resin and pour schedule for the geometry
A 2-inch-deep cavity does not mean you may safely pour 2 inches in one operation. Manufacturer limits can differ between small castings and broad river tables. TotalBoat ThickSet documentation, for example, distinguishes small mold casting depths from thinner river-table layers. Read the instructions for the exact formulation you buy.
Large masses of curing epoxy can generate dangerous heat. Follow the batch-size, temperature, layer-depth, and recoat requirements rather than trying to accelerate the job. Wear the personal protective equipment required by both component safety data sheets, provide ventilation, and protect skin and eyes from uncured material.
Allow for leaks, absorption, and finishing
The 10% allowance here is a planning choice, not a promise that every mold will behave the same way. Porous wood, small cavities, retained material in mixing cups, and edge losses can all consume resin. A manufacturer-approved seal coat may be a separate operation with its own material requirement.
Dry-fit and level the mold, check seams, and calculate any final surface coating independently. Keep a written batch record with measured amounts and pour locations. If the actual cavity differs substantially from your first measurements, revise the volume estimate instead of compensating with an improvised resin-to-hardener ratio.
Frequently asked questions
No. The 9.14-gallon example assumes an 8-inch-wide river, 2-inch depth, and 10% extra. A different channel geometry changes the result.